收藏本站
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
IGNITION INPUT (IGN)
The ignition input wakes the device. It also controls the Fail
mode activation. The signal is “high active”, meaning the
component is active in case of a logic high at the input.
FLASHER INPUT (FLASHER)
The flasher input wakes the device. It also controls the Fail
Mode activation. The signal is “high active”, meaning the
component is active in case of a logic high at the input.
FOG INPUT (FOG)
The fog input wakes the device. It also controls the Fail
Mode activation. The signal is “high active”, meaning the
component is active in case of a logic high at the input.
RESET INPUT (RST)
This input wakes the device when the RST pin is at
logic [1]. It is also used to initialize the device configuration
and the SPI faults registers when the signal is low. All SI/SO
registers described Table 8 and Table 11 are reset. The fault
management is not affected by RST .
CURRENT SENSE OUTPUT (CSNS)
The current sense output pin is an analog current output or
a voltage proportional to the temperature on the GND flag.
The routing to the external resistor is SPI programmable.
This current sense monitoring may be synchronized in
case of the OUT6 is not used. So, the current sense
monitoring can be synchronized with a rising edge on the
FETOUT pin (t CSNS(SYNC) ) if CSNS sync SPI bit is set to logic
[1]. Connection of the FETOUT-pin to a MCU input pin allows
the MCU to sample the CSNS-pin during a valid time-slot.
Since this falling edge is generated at the end of this time-
slot, upon a switch-off command, this feature may be used to
implement maximum current control.
CHARGE PUMP (CP)
An external capacitor is connected between this pin and
the VBAT pin. It is used as a tank for the internal charge
FET OUT OUTPUT (FETOUT)
This output pin is used to control an external MOSFET
(OUT6).
The high level of the FETOUT Output is V CC , if VBAT and
V CC are available, in case FETOUT is a controlled ON.
FETOUT is not protected if there is a short-circuit or under-
voltage on VBAT.
In case of a reverse battery, OUT6 is OFF.
FET IN INPUT (FETIN)
This input pin gives the current recopy of the external
MOSFET. It can be routed on CSNS output by a SPI
command.
SPI PROTOCOL DESCRIPTION
The SPI interface has a full-duplex, three-wire,
synchronous data transfer with four I/O lines associated with
it: Serial Clock (SCLK), Serial Input (SI), Serial Output (SO),
and Chip Select ( CS ).
The SI/SO pins of the 10XS3535 device follow a first-in,
first-out (D15 to D0) protocol, with both input and output
words transferring the most significant bit (MSB) first. All
inputs are compatible with 3.3 V and 5.0 V CMOS logic
levels, supplied by V CC .
The SPI lines perform the following functions:
SERIAL CLOCK (SCLK)
The SCLK pin clocks the internal shift registers of the
10XS3535 device. The SI pin accepts data into the input shift
register on the falling edge of the SCLK signal, while the SO
pin shifts data information out of the SO line driver on the
rising edge of the SCLK signal. It is important that the SCLK
pin be in a logic low state whenever CS makes any transition.
For this reason, it is recommended the SCLK pin be in a logic
[0] whenever the device is not accessed ( CS logic [1] state).
SCLK has a passive pull-down, R DWN . When CS is logic [1],
signals at the SCLK and SI pins are ignored and SO is tri-
stated (high-impedance) (see Figure 8 ).
pump. Its value is 100 nF ± 20%, 25 V maximum.
MC10XS3535
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
23
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
KIT13892VLEVBEJ KIT EVAL FOR MC13892
KIT17C724EPEVBE KIT FOR 17C7242CH HBRIDGE PWR IC
KIT33810EKEVME BOARD EVAL FOR MC33810
KIT33811EGEVBE KIT EVAL 33811 SOLENOID MON IC
KIT33812ECUEVME KIT DESIGN FOR 33812/S12P
KIT33812EKEVBE BOARD EVALUATION FOR MC33812
KIT33879AEKEVBE BOARD EVALUATION FOR MC33879
KIT33880DWBEVB KIT EVAL FOR MC33880 8X SW W/SPI
相关代理商/技术参数
KIT10XS4200EVBE 制造商:Freescale Semiconductor 功能描述:EVAL BOARD, MC10XS4200 HIGH SIDE SWITCH; Silicon Manufacturer:Freescale; Silicon Core Number:MC10XS4200; Kit Application Type:High Side Switch; Application Sub Type:-; Kit Contents:Eval Board MC10XS4200, CD ROM
KIT-1113C 制造商:ABIKO 功能描述:Bulk
KIT1116-400 制造商:Laird Technologies Inc 功能描述:ANTKIT,FG 128-137MHZ/ODB + FM2
KIT-113-175C 制造商:LG Corporation 功能描述:KIT TUNER 113-175C (113-175E +
KIT1133-P250 功能描述:ANTKIT GB8W15FT CABLE 制造商:laird technologies ias 系列:* 零件状态:在售 标准包装:1
KIT-11591 功能描述:ISP POGO ADAPTER KIT 制造商:sparkfun electronics 系列:- 零件状态:在售 套件类型:初级入门套件 主要用途:ISP Pogo 适配器 标准包装:1
KIT1167-120 制造商:Laird Technologies Inc 功能描述:ANT KIT GPS1575PW 20FT 制造商:Laird Technologies Inc 功能描述:ANTKIT,GPS1575PW/20FT
KIT1185-120 制造商:Laird Technologies Inc 功能描述:KIT ANT GPS 20FT 制造商:Laird Technologies Inc 功能描述:KIT1185-120